How to replace the fascia board behind the gutter?
Replacing the fascia board behind your gutter is a big project that can be done by homeowners, but it’s not easy.
It will take time and patience to complete this task correctly. It’s best left for professional installers who’ve installed plenty of these before. But if you’re up for it, here are some tips to help you get started.
Begin by checking the fascia board behind your gutters. If it’s old, you might want to replace it. Use a pry bar to remove the nails that are joining the existing fascia board pieces together. The nails should pop out easily once they’ve been loosened with the pry bar. Be prepared for some splintering of the wood.
There’s a safety concern here. Be sure to wear protective eyewear or goggles and gloves for this task, as splinters can go flying when working with wood.
If there are nails you can’t pop out easily, use a hammer to break them loose instead. It will be easier work if you work on one side of the fascia at a time. Work from the underside, so you can slide out any nails that happen to get stuck.
Buy the correct fascia board for your home.
The standard size is 20 inches wide and 5.5 inches high, but if you need a special order board for your home, it will have to be cut down at the local lumberyard or building supply center. You’ll get better results if you buy 3/4-inch thick wood instead of thinner pieces.
If you discover that there are more cracks than you thought, your best bet is to replace the fascia board entirely. You’ll be able to slide out any nails that are left in place with the only minimal splintering of the wood.
Once the nails have been pulled or broken free, cut off the remaining piece of wood with a reciprocating saw so you can slide it out.
Buy some new boards. Be sure they’re the right size by comparing them to the old boards you’ve removed. You’ll be able to work more quickly if you cut the new pieces of wood with a table saw but use your hands or a saw that’s powered by an electric motor for best results.
Purchase fasteners such as galvanized nails or screws and wood glue to make the fascia board secure. Nails will come in handy here, but if you want a seamless look, use the screws instead.
Use your hands to slide out the old nails from the new boards before you continue with this project. This is important because splinters usually occur when you’re hammering the nails in place. You’ll have a greater chance of completing this project successfully if you work with a smaller number of boards.
Drill pilot holes into both sides of each board and mark where to nail it in place. It will be easier to get all the pieces into position and nailed down, especially when working on solo projects.
Clean each board thoroughly with a rag soaked in soap and water. If you don’t clean the boards well, it will be easy for mold to grow on your new fascia after the project is done. This could destroy the look of your house or even make it uncomfortable to spend time inside.
Put on safety goggles to protect your eyes during this process
Nail each board into place. It will be easier to nail them in the right place if you have someone standing on the ground to hold up the boards while you hammer in the nails. Be sure you don’t hit any wires, pipes, or other electric or water lines that are running along your fascia line because it could damage important structures in your home.
This is a good time to choose the paint color for your new fascia board. You don’t have to paint it, but this camouflage will help hide any splinters or cracks in the wood that might be visible without such an addition.
Let the nails dry overnight and remove any excess nail pieces from the boards before you’re completely finished with the project. You can use a hammer and nail set for this task, but if you do it too soon, you might scratch up the newly painted fascia board.
If there are any cracks in your fascia boards that have appeared since they were installed, you may need to replace them. It’s easy to remove existing boards that have cracks, but if the wood is destroyed in multiple places or is too far gone to be used again, it’s time to make a trip to the lumberyard and get some new fascia boards for your house.
If you don’t want splinters around your home, use this method to cover up any problems with your fascia board. It’s a good way to prevent any moisture damage that you might notice in certain parts of your home.
Use a pry bar to remove nails
These nails are easy to pull out of the wood, but you may need to put on safety goggles if you don’t want pieces of wood flying into your face.
You’ll be able to see whether there’s a crack in the board or where it needs repairing once you remove the board from your fascia line. If you notice that any of the wood needs to be replaced, cut off that piece of wood and put it in a garbage bag for later use.
You may need to replace the fascia board if you notice some serious damage or if it’s an older style of board that has been installed on your home. You won’t have any problems with moisture buildup or mold growing in your home if you take off the old fascia and replace it with a new one.
If there are small cracks in the fascia board, simply fill them up with wood glue before heading out to purchase a new fascia board for the house. This will help prevent water from getting into the wood, which could lead to mold growth and other moisture-related problems.
Be sure that the wood glue is made for exterior use and is water-resistant to prevent it from peeling off during rain or snowstorms. It might take a few days before the wood glue dries, depending on your local climate conditions.
Before you start painting your new fascia board, be sure that any holes or splinters are repaired. Also, be sure to check the wood on your board for any obvious signs of mold growth. If you see any mold, scrape it off the board before painting begins.
You may want to cover up your fascia line with a thinner coat if you plan on using multiple paint colors in the same project. It’s important to have a solid base coat for this process or your more detailed paint colors will not show up well.
That’s all it takes to get started with fascia board replacement today! The entire project should only take you a few hours, especially if you have someone helping you in the long run. So if there are any problems with your fascia board, it’s time to fix them now.
Screw the new fascia board into place
With the nails in the right locations, you shouldn’t have any problems with your fascia board falling out as you drive over it. The wood glue will also help prevent water from seeping through the cracks and swelling up the fascia board.
After that, all you need to do is paint the new fascia boards with whatever coat of paint you want. Be sure to use exterior paint for this process to ensure that it won’t peel in the rain or snow. If any mold has formed on the wood during installation, scrape it off with a putty knife before painting the boards.
If you have any gaps in your fascia board, place a thin coat of wood glue on the edges that meet up perfectly. After that, simply drive the nails into the holes and cover them with a small dab of wood glue for extra protection. The cracks should be filled up by this point and water will no longer leak through to damage the fascia board.
Finally, once the paint has dried overnight, you can have your family and friends over for a barbecue to celebrate your new and improved fascia boards!
GET YOUR GUTTER GUARDS TODAY!
Hiring a professional may save you some time and money in
They will be able to ensure that your new gutter system is working properly and they will also be there for repairs that need to be made as time goes on.
When you have a professional install your rain gutters then they will ensure that everything lines up correctly so that water does not leak through where it should not. They will also make sure that the gutters are pitched properly so that the water drains out away from your home and not towards it.
If you want to have a new gutter system then contact a professional for more information. They can come out and look at your home so that they can give you a quote on the installation. This is much better than guessing how much something will cost and it will also help them determine if this type of work is even possible with the way your house is currently set up.